Porsche Cayenne Turbo (9PA) Technical Service Bulletin # 916/08 Date: 081006
PCM3(R) - Coding Logbook
PCM3- Logbook
Information:
Coding logbook
Model Year:
As of 2009
Restriction:
Only for vehicles with PCM3 (I-no. PF2).
NOTE:
- The optional electronic logbook for PCM3 supports the driver in maintaining a logbook by recording all relevant data for the type of trip
(private, business), much of it automatically, and reducing user input to a minimum. PCM3 automatically records every trip > 100 miles. Trip
recording starts as soon as the key is inserted in the ignition and ends when it is removed. PCM3 will automatically record the following data:
- Date/time of departure and arrival
- Mileage at the start and end of the trip
- Start and destination address (location, street, country)
- If data is to be transferred to a PC, the recorded data can be copied from the PCM3 via Bluetooth or the optional USB interface on the PCM3.
- After ordering, i.e. entering the part number and Vehicle Identification Number (VIN) in POLARIS Lock/Key parts order screen, the enabling
code should be displayed within one day once the VIN is entered in the Vehicle code information column in the PIWIS information system.
Parts Info:
955.044.900.29 --> Logbook
Work Procedure:
1. Connect battery charger. --> Workshop Manual '2X00IN01 Battery trickle charge'
2010 Porsche Cayenne Turbo (9PA) V8-4.8L Turbo Page 15
NOTICE:
Voltage drop
- Risk of irreparable damage to control unit
- Risk of damage to control unit
- Fault entries in the control unit
- Coding in the control unit is aborted
- Malfunctions in control unit, even during programming
- Switch off the ignition and remove the ignition key before disconnecting the control unit.
- Ensure that the power supply is not interrupted during programming.
- Connect a battery charger with a current rating of at least Nominal value 40 A to the vehicle battery.
INFORMATION
The PIWIS Tester 9718 instructions take precedence and in the event of a discrepancy these are the instructions that must be followed.
Deviations may occur with later software versions.
The procedure described here has been structured in general terms; different text or additions may appear in the PIWIS Tester 9718.
2. Code logbook in PCM3.
2.1. PIWIS Tester 9718 must be connected and ignition switched on.
2.2. Select vehicle type and "PCM3" control unit. Press F12 to continue.
2.3. Select Coding in the Cayenne PCM3 function selection. Press F12 to continue.
2.4. Select Enabling code in the Cayenne PCM3 coding function selection. Press IF121 to continue.
Information The PIWIS Tester 9718 displays the message not installed/not enabled/not operational.
2.5. Select Logbook enabling code in the Cayenne PCM3 enabling code menu. Then press F12
2.6. Enter enabling code. Press F8 to start coding. Wait until the message "Coding has been changed" appears. The PIWIS Tester 9718 then
displays the message installed/enabled/operational
2.7. Press F11 to exit the PCM3 menu. The system is initialized.
2.8. Once coding is complete, read out the fault memories of all systems, correct any existing faults and erase the fault memories.
2.9. Switch off ignition and disconnect the PIWIS Tester 9718.
3. Disconnect battery charger. --> Workshop Manual '2X00IN01 Battery trickle charge'
4. Carry out a function test.
INFORMATION Further information can be found in the PCM3 operating instructions.
4.1. Activate logbook.
4.2. Test-drive the vehicle, then check the list of trips.
4.3. Deactivate logbook.
4.5. Clear entries in logbook.
Working Time:
Disclaimer