Porsche Cayenne Turbo (9PA) Technical Service Bulletin # 913/08 Date: 090106
PCM3.0(R) - Cell Phone/Bluetooth(R) Interface
PCM3.0 - Bluetooth Hands-free Phone Interface (I-no. 9W5)
Information:
Retrofitting
Model Year:
As of 2009
Restriction:
2010 Porsche Cayenne Turbo (9PA) V8-4.8L Turbo Page 16
Only for vehicles with PCM3.0 and not in conjunction with telephone module (I-no. 9W1) and telephone module with handset (I-no. 9ZP).
Note:
The mobile phone preparation is available without a console for connecting mobile phones that support the hands-free profile (HFP) via Bluetooth.
When connected over HFP, PCM3.0 serves only as a hands-free facility. The mobile phone can remain packed. The telephone numbers from the
SIM card must be copied over manually, unlike with the telephone module. Only the basic functions of the mobile phone can be used using PCM3.0
(see PCM3.0 operating instructions). With this option, GSM is connected via the mobile phone antenna.
If a mobile phone is installed and activated even though the telephone module is installed, the telephone module is not required. Both systems cannot
be used at the same time.
After ordering, i.e. entering the part number and Vehicle Identification Number (VIN) in POLARIS Lock/Key parts order screen, the enabling code
should be displayed within one day once the VIN is entered in the Vehicle code information column in the PIWIS information system.
Parts Info:
955.044.902.25-->Mobile phone preparation, set
Parts List:
Materials:
--- -- Wrapping tape (commercially available)
Block diagram
2010 Porsche Cayenne Turbo (9PA) V8-4.8L Turbo Page 17
Tools:
PIWIS Tester 9718
Press-out tool set Nr. 155 Pos. 1
Work Procedure:
1. Preparatory work
1.1. Connect a battery charger,-->Workshop Manual '2XOOINO3 Battery trickle charging'
1.2. Remove PCM3.0.
1.3. Check that connector module C (coding: blue) --> Figure 2 is fitted in the PCM 3.0 central connector.
If not:
Continue with Step 2.
If it is:
Continue with Step 1.4.
1.4. Check that the microphone wire harness is installed.
2010 Porsche Cayenne Turbo (9PA) V8-4.8L Turbo Page 18
1.4.1. Press the lock down and pull connector module C --> Figure 3 -1- (coding: blue) out of the PCM 3.0 central connector --> Figure 3
-2- (--> Figure 3 -arrow B-).
1.4.2. Lift up the lock and pull the (12-pin) plug socket --> Figure 4-1- out of the plug carrier --> Figure 4 -arrow B-.
1.4.3. Are chambers 1 and 9 --> Figure 5 -2- of the (12-pin) plug socket used?
No:
Continue with Step 2.
Yes:
Insert (12-pin) plug socket into the plug carrier -- Figure 6 -2-. Continue with Step 3.
2. Install microphone wire harness.
2.1. Preparatory work
2.1.1. Remove trim panel under dashboard on the driver's side.--> Workshop Manual '701919 Removing and installing trim panel under
dashboard'
2010 Porsche Cayenne Turbo (9PA) V8-4.8L Turbo Page 19
2.1.2. Remove instrument cluster.--> Workshop Manual '902519 Removing and installing instrument cluster'
2.1.3. Remove A-pillar trim panel at the left and right.--> Workshop Manual '705719 Removing and installing A pillar trim panel
2.1.4. Unscrew screws from the sun visors at the left and right.--> Workshop Manual '682319 Removing and installing sun visor'
2.1.5. Remove front left grab handle.--> Workshop Manual '683519 Removing and installing front grab handle'
2.1.6. Remove roof console.--> Workshop Manual '601219 Removing and installing switch for sliding roof
2.2. Route wire harness for microphone.
2.2.1. Carefully pull down the headliner near the windscreen at the left side and route wire harness for microphone --> Figure 7 -1- as
follows.
Roof console --> wiring duct on roof --> Figure 7 -3-
--> along A-pillar --> instrument panel
--> to PCM installation slot
2010 Porsche Cayenne Turbo (9PA) V8-4.8L Turbo Page 20
2.2.2. Align wire harness for microphone
so that gap X between the microphone connector and junction (isolation point) of the roof assembly connector is 120 mm.
Then secure the wire harness for the microphone to the standard wire harness with a tie-wrap/wrapping tape.
2.3. Connect wire harness for microphone.
2.3.1. Crimp cable ring eyelet to BN 0.5sq. line (microphone wire harness) and secure at the ground point in the roof.
2.3.2. Only for vehicles with Bose Surround Sound System.
2010 Porsche Cayenne Turbo (9PA) V8-4.8L Turbo Page 21
Remove the locks from the standard microphone connector and the microphone connector on the microphone wire harness (retrofit
kit) --> Figure 13 -1-.
Press pin contacts out of the microphone connector on the microphone wire harness (retrofit kit).
Insert pin contact of line RD 0.5sq.--> Figure 13 -3- into chamber 1 and pin contact of line GN 0.5sq.--> Figure 13 -2- into
chamber 2 of the standard microphone connector.
Close the locks on the standard microphone connectors.
2.3.3. Cut off socket contacts --> Figure 14-2- on microphone wire harness (retrofit kit) and crimp new socket contacts --> Figure 14-1-
to the microphone wire harness (retrofit kit).
2.3.4. Only for vehicles with connector module C (coding: blue).
INFORMATION: Ensure socket contact is seated securely.
Insert socket contact of line RD 0.5(squared)--> Figure 15-1- into chamber 1 of the (12-pin) plug socket.
Insert socket contact of line GN 0.5(squared)--> Figure 15-2- into chamber 9 of the (12-pin) plug socket.
Slide (12-pin) plug socket --> Figure 16-1- into the plug carrier --> Figure 16-2- until the (12-pin) plug socket clicks into place.
2010 Porsche Cayenne Turbo (9PA) V8-4.8L Turbo Page 22
2.3.5. Only for vehicles without connector module C (coding: blue).
INFORMATION Ensure socket contact is seated securely.
Insert socket contact of line RD 0.5(squared) --> Figure 17-3- into chamber 1 of the (12-pin) plug socket (retrofit kit) --> Figure 17
-1-.
Insert socket contact of line GN 0.5(squared) --> Figure 17 -2- into chamber 9 of the (12-pin) plug socket (retrofit kit) --> Figure
17-1-.
Slide (12-pin) plug socket --> Figure 18-1- in direction of arrow -> Figure 18-3- into the plug carrier --> Figure 18 -2- until the
(12-pin) plug socket clicks into place.
2.3.6. Insert connector module C (coding: blue) --> Figure 19 -arrow- into the PCM3.0 central connector.
3. Install microphone.
2010 Porsche Cayenne Turbo (9PA) V8-4.8L Turbo Page 23
3.1. Unclip strip for switches --> Figure 20 -1-from the roof console.
3.2. Check to see if a microphone --> Figure 20 -2- is installed.
No microphone installed:
Install a new microphone (retrofit kit). --> Workshop Manual '915719 Removing and installing microphone for telephone'
Microphone installed:
Check that the part number of the standard microphone is 7L5 035 711 E.
If it is:
Install standard microphone again.
If not:
Replace standard microphone with a new microphone (retrofit kit).
4. Concluding work
4.1. Install PCM3.0.
4.2. Only for vehicles with microphone wire harness retrofitted.
4.2.1. Install trim panel under dashboard on the driver's side.
4.2.2. Install instrument cluster.
4.2.3. Install A-pillar trim panel at the left and right.
4.2.4. Screw in screws on the sun visors at the left and right. --> Workshop Manual '682319 Removing and installing sun visor'
4.2.5. Install front left grab handle. --> Workshop Manual '683519 Removing and installing front grab handle'
4.2.6. Install roof console. --> Workshop Manual '601219 Removing and installing switch for sliding roof
4.3. Connect a battery charger. --> Workshop Manual '2X00IN01 Battery trickle charging'
NOTICE
Voltage drop
- Risk of irreparable damage to control unit
- Risk of damage to control unit
- Fault entries in the control unit
- Coding in the control unit is aborted
- Malfunctions in control unit, even during programming
- Switch off the ignition and remove the ignition key before disconnecting the control unit.
- Ensure that the power supply is not interrupted during programming.
- Connect a battery charger with a current rating of at least Nominal value 40 A to the vehicle battery.
INFORMATION
- The PIWIS Tester 9718 instructions take precedence and in the event of a discrepancy these are the instructions that must be followed.
Deviations may occur with later software versions.
- The procedure described here has been structured in general terms; different text or additions may appear in the PIWIS Tester 9718.
4.4. Enable mobile phone preparation.
4.4.1. PIWIS Tester 9718 must be connected and ignition switched on.
4.4.2. Select vehicle type and run control unit search.
4.4.3. Select PCM3 control unit.
4.4.4. Select PCM3 in the PCM3 function selection menu. Press F12 to continue.
4.4.5. Select Coding in the PCM3 function selection menu. Press F12 to continue.
4.4.6. Select Enabling code in the PCM3/Coding menu. Press F12 to continue.
4.4.7. Select Enabling code for Bluetooth mobile phone preparation installed/not enabled/not functional in the PCM3 Enabling code
menu. Press F12 to continue.
4.4.8. Enter the enabling code and press F8 to start coding. PIWIS Tester 9718 then displays the message installed/enabled/functional,
4.4.9. Press F11 to return to the main menu. The system is initialized.
4.4.10. Once coding is complete, read out the fault memories of all systems, correct any existing faults and erase the fault memories.
4.4.11. Switch off ignition and disconnect the PIWIS Tester 9718.
4.5. Disconnect the battery charger. --> Workshop Manual '2X00IN01 Battery trickle charging'
2010 Porsche Cayenne Turbo (9PA) V8-4.8L Turbo Page 24
Working Time:
Disclaimer
PCM3.0(R) - Cell Phone/Bluetooth(R) Interface
PCM3.0 - Bluetooth Hands-free Phone Interface (I-no. 9W5)
Information:
Retrofitting
Model Year:
As of 2009
Restriction:
2010 Porsche Cayenne Turbo (9PA) V8-4.8L Turbo Page 16
Only for vehicles with PCM3.0 and not in conjunction with telephone module (I-no. 9W1) and telephone module with handset (I-no. 9ZP).
Note:
The mobile phone preparation is available without a console for connecting mobile phones that support the hands-free profile (HFP) via Bluetooth.
When connected over HFP, PCM3.0 serves only as a hands-free facility. The mobile phone can remain packed. The telephone numbers from the
SIM card must be copied over manually, unlike with the telephone module. Only the basic functions of the mobile phone can be used using PCM3.0
(see PCM3.0 operating instructions). With this option, GSM is connected via the mobile phone antenna.
If a mobile phone is installed and activated even though the telephone module is installed, the telephone module is not required. Both systems cannot
be used at the same time.
After ordering, i.e. entering the part number and Vehicle Identification Number (VIN) in POLARIS Lock/Key parts order screen, the enabling code
should be displayed within one day once the VIN is entered in the Vehicle code information column in the PIWIS information system.
Parts Info:
955.044.902.25-->Mobile phone preparation, set
Parts List:
Materials:
--- -- Wrapping tape (commercially available)
Block diagram
2010 Porsche Cayenne Turbo (9PA) V8-4.8L Turbo Page 17
Tools:
PIWIS Tester 9718
Press-out tool set Nr. 155 Pos. 1
Work Procedure:
1. Preparatory work
1.1. Connect a battery charger,-->Workshop Manual '2XOOINO3 Battery trickle charging'
1.2. Remove PCM3.0.
1.3. Check that connector module C (coding: blue) --> Figure 2 is fitted in the PCM 3.0 central connector.
If not:
Continue with Step 2.
If it is:
Continue with Step 1.4.
1.4. Check that the microphone wire harness is installed.
2010 Porsche Cayenne Turbo (9PA) V8-4.8L Turbo Page 18
1.4.1. Press the lock down and pull connector module C --> Figure 3 -1- (coding: blue) out of the PCM 3.0 central connector --> Figure 3
-2- (--> Figure 3 -arrow B-).
1.4.2. Lift up the lock and pull the (12-pin) plug socket --> Figure 4-1- out of the plug carrier --> Figure 4 -arrow B-.
1.4.3. Are chambers 1 and 9 --> Figure 5 -2- of the (12-pin) plug socket used?
No:
Continue with Step 2.
Yes:
Insert (12-pin) plug socket into the plug carrier -- Figure 6 -2-. Continue with Step 3.
2. Install microphone wire harness.
2.1. Preparatory work
2.1.1. Remove trim panel under dashboard on the driver's side.--> Workshop Manual '701919 Removing and installing trim panel under
dashboard'
2010 Porsche Cayenne Turbo (9PA) V8-4.8L Turbo Page 19
2.1.2. Remove instrument cluster.--> Workshop Manual '902519 Removing and installing instrument cluster'
2.1.3. Remove A-pillar trim panel at the left and right.--> Workshop Manual '705719 Removing and installing A pillar trim panel
2.1.4. Unscrew screws from the sun visors at the left and right.--> Workshop Manual '682319 Removing and installing sun visor'
2.1.5. Remove front left grab handle.--> Workshop Manual '683519 Removing and installing front grab handle'
2.1.6. Remove roof console.--> Workshop Manual '601219 Removing and installing switch for sliding roof
2.2. Route wire harness for microphone.
2.2.1. Carefully pull down the headliner near the windscreen at the left side and route wire harness for microphone --> Figure 7 -1- as
follows.
Roof console --> wiring duct on roof --> Figure 7 -3-
--> along A-pillar --> instrument panel
--> to PCM installation slot
2010 Porsche Cayenne Turbo (9PA) V8-4.8L Turbo Page 20
2.2.2. Align wire harness for microphone
so that gap X between the microphone connector and junction (isolation point) of the roof assembly connector is 120 mm.
Then secure the wire harness for the microphone to the standard wire harness with a tie-wrap/wrapping tape.
2.3. Connect wire harness for microphone.
2.3.1. Crimp cable ring eyelet to BN 0.5sq. line (microphone wire harness) and secure at the ground point in the roof.
2.3.2. Only for vehicles with Bose Surround Sound System.
2010 Porsche Cayenne Turbo (9PA) V8-4.8L Turbo Page 21
Remove the locks from the standard microphone connector and the microphone connector on the microphone wire harness (retrofit
kit) --> Figure 13 -1-.
Press pin contacts out of the microphone connector on the microphone wire harness (retrofit kit).
Insert pin contact of line RD 0.5sq.--> Figure 13 -3- into chamber 1 and pin contact of line GN 0.5sq.--> Figure 13 -2- into
chamber 2 of the standard microphone connector.
Close the locks on the standard microphone connectors.
2.3.3. Cut off socket contacts --> Figure 14-2- on microphone wire harness (retrofit kit) and crimp new socket contacts --> Figure 14-1-
to the microphone wire harness (retrofit kit).
2.3.4. Only for vehicles with connector module C (coding: blue).
INFORMATION: Ensure socket contact is seated securely.
Insert socket contact of line RD 0.5(squared)--> Figure 15-1- into chamber 1 of the (12-pin) plug socket.
Insert socket contact of line GN 0.5(squared)--> Figure 15-2- into chamber 9 of the (12-pin) plug socket.
Slide (12-pin) plug socket --> Figure 16-1- into the plug carrier --> Figure 16-2- until the (12-pin) plug socket clicks into place.
2010 Porsche Cayenne Turbo (9PA) V8-4.8L Turbo Page 22
2.3.5. Only for vehicles without connector module C (coding: blue).
INFORMATION Ensure socket contact is seated securely.
Insert socket contact of line RD 0.5(squared) --> Figure 17-3- into chamber 1 of the (12-pin) plug socket (retrofit kit) --> Figure 17
-1-.
Insert socket contact of line GN 0.5(squared) --> Figure 17 -2- into chamber 9 of the (12-pin) plug socket (retrofit kit) --> Figure
17-1-.
Slide (12-pin) plug socket --> Figure 18-1- in direction of arrow -> Figure 18-3- into the plug carrier --> Figure 18 -2- until the
(12-pin) plug socket clicks into place.
2.3.6. Insert connector module C (coding: blue) --> Figure 19 -arrow- into the PCM3.0 central connector.
3. Install microphone.
2010 Porsche Cayenne Turbo (9PA) V8-4.8L Turbo Page 23
3.1. Unclip strip for switches --> Figure 20 -1-from the roof console.
3.2. Check to see if a microphone --> Figure 20 -2- is installed.
No microphone installed:
Install a new microphone (retrofit kit). --> Workshop Manual '915719 Removing and installing microphone for telephone'
Microphone installed:
Check that the part number of the standard microphone is 7L5 035 711 E.
If it is:
Install standard microphone again.
If not:
Replace standard microphone with a new microphone (retrofit kit).
4. Concluding work
4.1. Install PCM3.0.
4.2. Only for vehicles with microphone wire harness retrofitted.
4.2.1. Install trim panel under dashboard on the driver's side.
4.2.2. Install instrument cluster.
4.2.3. Install A-pillar trim panel at the left and right.
4.2.4. Screw in screws on the sun visors at the left and right. --> Workshop Manual '682319 Removing and installing sun visor'
4.2.5. Install front left grab handle. --> Workshop Manual '683519 Removing and installing front grab handle'
4.2.6. Install roof console. --> Workshop Manual '601219 Removing and installing switch for sliding roof
4.3. Connect a battery charger. --> Workshop Manual '2X00IN01 Battery trickle charging'
NOTICE
Voltage drop
- Risk of irreparable damage to control unit
- Risk of damage to control unit
- Fault entries in the control unit
- Coding in the control unit is aborted
- Malfunctions in control unit, even during programming
- Switch off the ignition and remove the ignition key before disconnecting the control unit.
- Ensure that the power supply is not interrupted during programming.
- Connect a battery charger with a current rating of at least Nominal value 40 A to the vehicle battery.
INFORMATION
- The PIWIS Tester 9718 instructions take precedence and in the event of a discrepancy these are the instructions that must be followed.
Deviations may occur with later software versions.
- The procedure described here has been structured in general terms; different text or additions may appear in the PIWIS Tester 9718.
4.4. Enable mobile phone preparation.
4.4.1. PIWIS Tester 9718 must be connected and ignition switched on.
4.4.2. Select vehicle type and run control unit search.
4.4.3. Select PCM3 control unit.
4.4.4. Select PCM3 in the PCM3 function selection menu. Press F12 to continue.
4.4.5. Select Coding in the PCM3 function selection menu. Press F12 to continue.
4.4.6. Select Enabling code in the PCM3/Coding menu. Press F12 to continue.
4.4.7. Select Enabling code for Bluetooth mobile phone preparation installed/not enabled/not functional in the PCM3 Enabling code
menu. Press F12 to continue.
4.4.8. Enter the enabling code and press F8 to start coding. PIWIS Tester 9718 then displays the message installed/enabled/functional,
4.4.9. Press F11 to return to the main menu. The system is initialized.
4.4.10. Once coding is complete, read out the fault memories of all systems, correct any existing faults and erase the fault memories.
4.4.11. Switch off ignition and disconnect the PIWIS Tester 9718.
4.5. Disconnect the battery charger. --> Workshop Manual '2X00IN01 Battery trickle charging'
2010 Porsche Cayenne Turbo (9PA) V8-4.8L Turbo Page 24
Working Time:
Disclaimer