Vehicle: All Technical Service Bulletins
Cell Phone - Bluetooth(R) Hands-Free Interface
9
20/09 ENU 9187
Oct 8, 2009
PCM3.1 - Bluetooth Hands-free Phone Interface (I-no. 619)
Information:
Retrofitting
Model Year:
As of 2010
Restriction:
Only for vehicles with PCM3.1.
Information:
The mobile phone preparation is available without a console for connecting mobile phones that support the hands-free profile (HFP) via
Bluetooth(R). When connected via HFP, PCM3. 1 serves only as a hands-free facility. Only the basic functions of the mobile phone can be used
using PCM3.1. With this option, GSM is connected via the mobile phone antenna.
For more information on operation and the various functions available, refer to the "PCM3.1" operating instructions.
Vehicles with the optional equipment telephone module (I-no. 666) and/or voice control (I-no. 671) already have the required microphone installed. The microphone wire harness and the roof console do not need to be retrofitted for these options.
Information
The following data is required in order to activate the function (enabling code):
^ Part number of the retrofit kit
^ Vehicle identification number (VIN) of the vehicle to be converted
^ Order number used for ordering parts
These components require a VIN-specific enabling code and will not function without it. To get the enabling code, order the applicable kit via your
normal parts channels (POLARIS). You must then submit a PTEC/PTAR with the correct VIN, Part Number and PCNA order number to PCNA
Parts Support. The PTEC will be returned to you in 1 + working days, advising you that the code is now displayed in the PIWIS System. Consult
Parts Bulletin GR13D9O for additional ordering details.
Once you confirm the order, the "Bluetooth mobile phone preparation" enabling code can be obtained from the vehicle code information for the
vehicle to be converted in the PPN (PIWIS).
Parts Info:
970.044.900.32
--> Mobile phone preparation, set
Also order the corresponding roof console!
Parts List:
Tools:
Block diagram:
Information
For a better understanding of the system layout, see system diagram, Figure 3.
Work Procedure: 1
Only for vehicles without telephone module (I-no. 666) or voice control (I-no. 671):
-----------------------------------------------------Page 1-----------------------------------------------------
2010 Porsche Panamera Turbo (970) V8-4.8L Turbo
Preparatory work.
1.1 Remove the PCM3.1. --> Workshop Manual '911019 Removing and installing PCM display and operator control unit'
1.2 Remove roof console. --> Workshop Manual '708319 Removing and installing roof console'
1.3 Remove sun visor on driver's side. --> Workshop Manual '682319 Removing and installing sun visor'
1.4 Remove A-pillar trim on driver's side. --> Workshop Manual '705719 Removing and installing A-pillar trim'
1.5 Remove front grab handle on driver's side. --> Workshop Manual '683519 Removing and installing front grab handle'
1.6 Remove rear left grab handle. --> Workshop Manual '683719 Removing and installing rear grab handle'
1.7 Remove rear left reading light. --> Workshop Manual '964619 Removing and installing reading light'
1.8 Remove upper part of B-pillar trim on driver's side. --> Workshop Manual '706719 Removing and installing B-pillar trim panel'
1.8.1 Remove air vent.
1.8.2 Pull off cap and unscrew fastening screw.
1.8.3 Unclip upper part of B-pillar trim.
1.9 Disconnect the battery. --> Workshop Manual '2XOOIN Work instructions after disconnecting the battery'
1.10 Remove trim panel under dashboard on the driver's side. --> Workshop Manual '701919 Removing and installing trim panel under
dashboard'
1.11 Remove instrument cluster. --> Workshop Manual '902519 Removing and installing instrument cluster'
1.12 Detach front headliner on driver's side.
1.12.1 Unscrew fastening screws --> Figure 4-1- close to the roof console.
1.12.2 Hold the headliner at the positions shown --> Figure 5-A and B- and pull it down slightly with a strong jerk at position --> Figure
5-B-so that the pin --> Figure 5-1-comes out of the roof.
2 Only for vehicles without telephone module (I-no. 666) or voice control (I-no. 671):
Install wire harness for microphone.
2.1 Unclip standard wire harness for roof --> Figure 6-1- close to the windshield.
2.2 Connect wire harness for microphone to the roof console connector at the right --> Figure 7-arrow-.
2.2.1 Open the clip --> Figure 8-1-. Press the locking mechanism down --> Figure 8-2- and pull the plug socket --> Figure 8-3-
out of the plug carrier.
Information
Use the end of the line with two socket contacts.
Information
Ensure socket contact is seated securely.
2.2.2 Insert socket contact of line BU --> Figure 9 -1- into chamber 1 and socket contact of line GY --> Figure 9-2- into chamber
2.
2.2.3 Insert plug socket into plug carrier --> Figure 10-arrow A-. Close the clip --> Figure 10-arrow B-.
2.3 Secure shielding line --> Figure 11-1- to the standard wire harness --> Figure 11 -2- with wrapping tape.
2.4 Route microphone wire harness as follows:
Roof console --> roof wire harness ->
Figure 12-1- --> A-pillar --> instrument panel
-----------------------------------------------------Page 2-----------------------------------------------------
2010 Porsche Panamera Turbo (970) V8-4.8L Turbo
--> Figure 13 --> PCM installation slot --> Figure 14-1-
Information
If connector module C (coding: blue) is not installed, use connector module C from the retrofit kit.
2.5 Connect wire harness for microphone to the blue connector module C --> Figure 15-1-.
2.5.1 Press locking mechanism down --> Figure 16-arrow -A- and pull connector module C --> Figure 16-1-out of the PCM central
connector --> Figure 16-2- (--> Figure 16-arrow B-).
2.5.2 Lift up locking mechanism --> Figure 17-arrow A- and pull the plug socket --> Figure 17 - 1- out of the plug carrier --> Figure
17-arrow B-.
Information
Ensure socket contact is seated securely.
2.5.3 Insert socket contact of line GY into chamber 1 --> Figure 18-1- of the plug socket.
Insert socket contact of line BU into chamber 9 --> Figure 18-2- of the plug socket.
Insert socket contact of line BK into chamber 3 --> Figure 18-3-of the plug socket.
2.5.4 Insert plug socket --> Figure 19 -1- into plug carrier --> Figure 19 -2-.
2.5.5 Insert connector module C into PCM central connector --> Figure 20-arrow-.
3 Only for vehicles without telephone module (I-no. 666) or voice control (I-no. 671):
Concluding work.
3.1 Clip in standard wire harness for roof --> Figure 21-1- close to the windshield.
3.2 Screw in fastening screws --> Figure 22 -1- close to the roof console.
3.3 Fit upper part of B-pillar trim at the left. --> Workshop Manual '706719 Removing and installing B-pillar trim panel'
3.3.1 Fit upper part of B-pillar trim.
3.3.2 Screw in fastening screw. Fit cap.
3.3.3 Fit air vent.
3.4 Install rear left grab handle. --> Workshop Manual '683719 Removing and installing rear grab handle'
3.5 Install rear left reading light. --> Workshop Manual '964619 Removing and installing reading light'
3.6 Install front grab handle on driver's side. --> Workshop Manual '683519 Removing and installing front grab handle'
3.7 Install A-pillar trim on driver's side. --> Workshop Manual '705719 Removing and installing A-pillar trim panel'
3.8 Install sun visor on driver's side. --> Workshop Manual '682319 Removing and installing sun visor'
3.9 Install roof console. --> Workshop Manual '708319 Removing and installing roof console'
3.10 Install instrument cluster. --> Workshop Manual '902519 Removing and installing instrument cluster'
3.11 Install trim panel under the dashboard. --> Workshop Manual '701919 Removing and installing trim panel under dashboard'
3.12 Install PCM3.1. --> Workshop Manual '911019 Removing and installing PCM display and operator control unit'
3.13 Connect the battery. --> Workshop Manual '2X00IN Work instructions after disconnecting the battery'
Voltage drop
^ Risk of irreparable damage to control unit
^ Risk of damage to control unit
-----------------------------------------------------Page 3-----------------------------------------------------
2010 Porsche Panamera Turbo (970) V8-4.8L Turbo
^ Fault entries in the control unit Coding in the control unit is aborted
^ Malfunctions in control unit, even during programming
--> Switch off the ignition and remove the ignition key before disconnecting the control unit.
--> Ensure that the power supply is not interrupted during programming.
--> Connect a battery charger with a current rating of at least Nominal value 40 A to the vehicle battery.
Information
The PIWIS Jester 2 9818 instructions take precedence since the description may be different with later Tester releases.
The procedure described here has been structured in general terms; different text or additions may appear on the PIWIS Tester 2 9818.
4 Code the mobile phone preparation.
4.1 Connect battery charger. ~ Workshop Manual '2X00IN Battery trickle charge'
4.2 PIWIS Jester 2 9818 must be connected and ignition switched on.
4.3 Select the vehicle type and select PCM control unit. Press [F12] to continue.
4.4 Switch to the Maintenance/repairs menu. Select the Function enable function. Then press [F12].
4.5 Select the Bluetooth mobile phone preparation function.
Enter the enabling code and confirm by touching the Status cell. Press [F8] to continue. Wait until the message Enable was successful appears Press [F12] to continue.
4.6 Touch the Overview cell to return to the control unit overview Press [F7] to switch to the Additional menu.
Select the Management of vehicle order function. Press [F12] until M numbers appears in the Value group column.
Select the coding value 619. When you touch the Inst. cell - behind the Bluetooth mobile phone preparation value - a tick (check mark symbol) appears.
Press [F8] to save the value. Wait until the message Modified values have been buffered appears. Press [F12] until [F8] can be activated.
Write values by pressing [F8]. Wait until the message Creation of vehicle order has been completed appears.
Press [F12] to switch to Log management. Open the log and check that vehicle equipment 619 Bluetooth mobile phone preparation is entered. Close the log.
4.7 Press [F12] to switch to the control unit overview.
Select PCM control unit. Then press [F12]. Switch to the Codings/adaptations menu.
Select Automatic coding with coding rules. Then press [F12]. Wait until the message Coding has been completed successfully appears. Then press [F12].
4.8 Once coding is complete, read out the fault memories of all Systems, correct any existing faults and erase the fault memories. --> Workshop
Manual '0X01IN Diagnostic system:
Reading out fault memory and activating systems'
4.9 Switch off ignition and disconnect the PIWIS Tester 29818.
4.10 Disconnect the battery charger. --> Workshop Manual '2X00IN Battery trickle charging'
Working Time:
Disclaimer
-----------------------------------------------------Page 4-----------------------------------------------------