Showing posts with label manufacturer. Show all posts
Showing posts with label manufacturer. Show all posts

Sunday, 19 June 2022

2000 Porsche Boxster (986) F6-2.7L A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Page 228


Test Point 34



TEST POINT 34



Passenger Compartment monitoring Sensor Positive Short Or Faulty



Fault Code 34



Fault Effect: No passenger compartment monitoring



Procedure



1. Pull off plug I on the alarm control unit.



2. Pull off the plug at the passenger compartment monitoring sensor.



3. Voltmeter at plug I, alarm control unit pin 24 and ground. Switch on ignition.



Display: 0 Volts



If battery voltage is displayed check the wiring harness for pinches and chafing damage.



If no fault is detected in the wiring, replace the passenger compartment monitoring sensor.



Test Point 35



TEST POINT 35



Passenger Compartment monitoring Sensor Faulty



Fault Code 35



Fault Effect: No passenger compartment monitoring



Procedure



1. Pull off plug I on the alarm control unit.



2. Pull off the plug at the passenger compartment monitoring sensor.



3. Voltmeter at plug I, alarm control unit pin 24 and ground. Switch on ignition.



Display: 0 Volts



If battery voltage is displayed check the wiring harness for pinches and chafing damage.



If no fault is detected in the wiring, replace the passenger compartment monitoring sensor.



Test Point 36



TEST POINT 36



Passenger Compartment monitoring Sensor Positive Short Or Faulty



Fault Code 36



Fault Effect: No passenger compartment monitoring



Procedure



Replace passenger compartment monitoring sensor.



Test Point 37



TEST POINT 37



Passenger Compartment monitoring Sensor Faulty



Fault Code 37



Fault Effect: No passenger compartment monitoring

2000 Porsche Boxster (986) F6-2.7L A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Page 395


Diagnosis/troubleshooting



800A CDR23



800A CDR23



CAN Comfort Signal Fault, Air-Conditioning System



Diagnostic conditions



- Ignition on



- Start CDR23



Possible cause of fault



- Open circuit in CAN Bus Comfort (high)



- Open circuit in CAN Bus Comfort (low)



The CAN comfort is connected to the following control units:



- PCM2 as of model year 2003



- Instrument cluster



- Air-conditioning control unit

Saturday, 18 June 2022

2000 Porsche Boxster (986) F6-2.7L A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Page 171


Work Instruction 8 - 10

2000 Porsche Boxster (986) F6-2.7L A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Page 305


Work Instruction 1



Fault Code 9110



Fault Code 9110



DME Control Unit



Diagnostic conditions



- Ignition on



Possible cause of fault



- Short circuit between CAN-high and ground



- Open circuit of CAN-high drive



- Open circuit of CAN-low drive



- DME control unit faulty



NOTE:



The CAN drive bus is connected to the following control units:



- DME



- Tiptronic



- PSM and steering angle sensor



- Instrument cluster



Affected pin



Instrument cluster connector A, pin 15 and pin 31 (CAN drive)



Diagnosis/Troubleshooting



Work Instruction 1 - 4



Fault Code 9111



Fault Code 9111



PSM/ABS Control Unit



Diagnostic conditions



- Ignition on



Possible cause of fault



- Open circuit of CAN-high drive

2000 Porsche Boxster (986) F6-2.7L A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Page 61


- Short circuit between CAN-high and ground



- Open circuit of CAN-high drive



- Open circuit of CAN-low drive



- DME control unit faulty



NOTE:



- The CAN drive bus is connected to the following control units:



- DME



- Tiptronic



- PSM and steering angle sensor



- Instrument cluster



Affected pin



Instrument cluster connector A, pin 15 and pin 31 (CAN drive)



Diagnosis/troubleshooting



Fault Code 9111



Fault Code 9111



PSM/ABS Control Unit



Diagnostic conditions



- Ignition on



Possible cause of fault



- Open circuit of CAN-high drive



- Open circuit of CAN-low drive



- Due to a faulty component, the PSM system has switched off or PSM control unit is faulty



NOTE:



The CAN drive bus is connected to the following control units:



- DME



- Tiptronic



- PSM and steering angle sensor



- Instrument cluster



Affected pin



Instrument cluster connector A, pin 15 and pin 31 (CAN drive)



Diagnosis/Troubleshooting

Friday, 17 June 2022

2000 Porsche Boxster (986) F6-2.7L A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Page 422


2. Connect ohmmeter to plug, pin 23 and ground.



Plug of child seat not inserted.



Display: approx. 2 kOhms



Plug of child seat inserted.



Display: approx. 260 Ohms



3. Inspect the wiring harness to the triggering unit for pinches and chafing damage.



Test Point 8



Test point 8



Control module



Fault code >= 100



Replace the triggering unit.



Test Point 9



Test point 9



Unknown fault code



Fault code XXX



1. Inspect the ground points for corrosion.



2. Inspect the ignition on the secondary side.



3. Clear the fault memory.



Test Point 1



Test point 1



Ignition circuit, driver



Fault codes 04, 05, 20, 21, 36



1. Remove driver's airbag unit.



2. Attach the special tool 9516 instead of the airbag unit.



3. Clear the fault memory.



4. Check whether the fault appears again.



a. If the fault does not appear again, replace the airbag unit.



b. If the fault appears again, disconnect plug connection to the contact unit and attach special tool 9516/1.

2000 Porsche Boxster (986) F6-2.7L A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Page 420


Test Point 2



Test point 2



Ignition circuit, passenger



Fault codes 10, 11, 26, 27, 39



1. Disconnect the plug connection to the passenger's airbag unit.



2. Attach the special tool 9516 in conjunction with special tool 9566.



3. Clear the fault memory.



4. Check whether the fault appears again.



a. If the fault does not appear again, replace the passenger's airbag unit.



b. If the fault appears again, check the wiring harness for pinches and chafing damage.



c. If no fault is found on the wiring harness, replace the triggering unit.



NOTE:



- Fault code 39



- This fault path is checked only once after the ignition is switched on.



Proceed as described below to determine whether the fault was eliminated:



1. Clear the fault memory.



2. Switch off ignition.



3. Remove ignition key.



4. Switch on ignition.

Thursday, 16 June 2022

2000 Porsche Boxster (986) F6-2.7L A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Page 198


If display < 5 ohms, check wiring harness for chafing and pinching damage.



Test Point 19



TEST POINT 19



Status Lead, Signal Converter Short To B+



Fault Code 19



Fault Effect: No engine start possible



Procedure



1. Pull plug I off the alarm system control module.



2. Pull off the plug on the signal converter for the transponder.



3. Voltmeter at alarm system control module plug I, pin 4 and ground. Switch ignition on.



Display: 0 Volts



If battery voltage is displayed, check the wiring harness for pinches and chafing damage.



Test Point 20



TEST POINT 20



Status Lead, Signal Converter Short To Ground



Fault Code 20



Fault Effect: No engine start possible



Procedure



1. Pull plug I off the alarm system control module.



2. Pull off the plug on the signal converter for the transponder.



3. Ohmmeter at alarm system control module plug I, pin 12 and ground.



Display: infinity



If display < 5ohms, check wiring harness for chafing and pinching damage.



Test Point 21



TEST POINT 21



W lead (DmE Immobilizer) Open Circuit



Fault Code 21



Fault Effect: No engine start possible



Procedure



1. Pull plug I off the alarm system control module.



2. Unplug the DmE (ECm) connector.



3. Ohmmeter at alarm system control module plug I, pin 23 and ECm connector pin 88 or, as from model year '00, plug I, pin 3.



Display: < 5 ohms



Note:



The wire is routed via the plug connection X 3/1, pin 14 (up to and including model year '99, direct wire as from model year '00).



4. Ohmmeter at alarm system control module plug I, pin 23 and ground

2000 Porsche Boxster (986) F6-2.7L A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Page 443


Diagnostic conditions



- Ignition on



- PCM2 on



Possible cause of fault



- Telephone control module faulty



Diagnosis/troubleshooting



9606 Telephone/Telematics



9606 Telephone/telematics



No MOST communication



Diagnostic conditions



- Ignition on



- PCM2 on



Possible cause of fault



- Short circuit between the two CAN leads (CAN-high and CAN-low)



- Short circuit between CAN-high (drive) and ground



- Short circuit between CAN-low (drive) and voltage



- A faulty control unit connected to CAN drive bus



NOTE:



- The CAN drive bus is connected to the following control units:



Affected pins



- DME



- Tiptronic



- PSM and steering angle sensor



- Instrument cluster



NOTE: The plug connections of control units connected to the CAN drive bus are disconnected for trouble shooting. This has the effect that



additional CAN relevant fault codes such as "9110 DME control unit" are stored in the fault memory of the instrument cluster. These fault codes



should be initially ignored and should be deleted on completion of the troubleshooting.



Affected pin



Instrument cluster connector A, pin 15 and pin 31



Diagnosis/troubleshooting

2000 Porsche Boxster (986) F6-2.7L A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Page 326


Work Instruction 1 - 2



8004 PCM2 MMI



8004 PCM2 - MMI



Single CD Drive Overheating



- Battery temperature too high



Diagnostic conditions



- Ignition on



- PCM2 on



- Start the single CD player



Possible cause of fault



- Exterior and interior temperature very high



- Operation of heater



Diagnosis/Troubleshooting

Wednesday, 15 June 2022

2000 Porsche Boxster (986) F6-2.7L A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Page 183


- Check PIN 6 and PIN 7 of the control module connector (visual inspection for deformation).



Test Point 7



TEST POINT 7



Front Right Speed Sensor, Open Circuit / Short To Ground / Short To B+



DTC 4200



General procedure as for test point 6/diagnostic trouble code 4205.



- Speed sensor signal: Check with the Porsche System Tester 2 via the Actual values menu (call up front right wheel speed).



- Internal resistance/continuity between PIN 4 and PIN 5 on the control module connector.



Test Point 8



TEST POINT 8



Rear Right Speed Sensor, Open Circuit/ Short To Ground / Short To B+



DTC 4210



General procedure as for test point 6/diagnostic trouble code 4205.



- Speed sensor signal: Check with the Porsche System Tester 2 via the Actual values menu (call up rear right wheel speed).



- Internal resistance/continuity between PIN 1 and PIN 2 on the control module connector.



Test Point 9



TEST POINT 9



Rear Left Speed Sensor, Open Circuit / Short To Ground / Short To B+



DTC 4215



General procedure as for test point 6/diagnostic trouble code 4205.



- Speed sensor signal: Check with the Porsche System Tester 2 via the Actual values menu (call up rear left wheel speed).



- Internal resistance/continuity between PIN 8 and PIN 9 on the control module connector.



Test Point 10



TEST POINT 10



Control module Faulty



DTC 4226, 4231, 4236, 4241, 4246, 4251, 4256, 4261



Actual fault: ABS solenoid valve faulty.



The System Tester 2 can be used to check the function of the ABS solenoid valves via the Drive links menu, sub-menu maintain pressure and



Reduce pressure.



If the control module or ABS solenoid valves are damaged, the complete hydraulic unit with integrated control module must be replaced.



Important: Before replacing the hydraulic unit, check whether:



- ground is connected to control module connector PIN 16 (from ground point 2) and PIN 19 (from electronics ground). The locations of the

2000 Porsche Boxster (986) F6-2.7L A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Page 232


Test Point 3



TEST POINT 3



Inside Sensor On Left Does Not Function



Fault Code 3



This fault is stored in the following cases:



1. Open circuit in the supply lead to the inside sensor on left.



2. Short to B+ in the supply lead to the inside sensor on left.



3. Short to ground in the supply lead to the inside sensor on left.



Elimination:



- Delete fault memory, disengage reverse gear and switch off ignition. Then switch on ignition, engage reverse gear again and read out fault



memory.



- If the fault reappears, check plug on sensor for open circuit.



- If there is no open circuit, check for continuity with an ohmmeter from sensor connector pin 1 to pin 4 and pin 1 to pin 2. Continuity should



not be measured.



- If no short circuit can be detected, replace sensor.



Test Point 4



TEST POINT 4



Outside Sensor On Left Does Not Function



Fault Code 4



This fault is stored in the following cases:



1. Open circuit in the supply lead to the outside sensor on left.



2. Short to B+ in the supply lead to the outside sensor on left.



3. Short to ground in the supply lead to the outside sensor on left.



Elimination:



- Delete fault memory, disengage reverse gear and switch off ignition. Then switch on ignition, engage reverse gear again and read out fault



memory.



- If the fault reappears, check plug on sensor for open circuit.



- If there is no open circuit, check for continuity with an ohmmeter from sensor connector pin 1 to pin 4 and pin 1 to pin 2. Continuity should



not be measured.



- If no short circuit can be detected, replace sensor.



Test Point 5



TEST POINT 5



Control module Supply Voltage > 16.5 V or < 9 V



Fault Code 5



This fault is stored in the following cases:



1. Low vehicle voltage



2. If there is a fault in the generator



Elimination:



- Examine battery and generator voltages.



- Select Control module supply voltage and Sensor supply voltage under the menu item Actual values, and check the values with reverse gear



engaged and the engine running.



Control module supply voltage display: approx. 12 Volts



Sensor supply voltage display: approx. 8 Volts



- Delete fault memory, disengage reverse gear and switch off ignition. Then switch on ignition, engage reverse gear again and read out fault

2000 Porsche Boxster (986) F6-2.7L A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Page 167


Work Instruction 1 - 2



Work Instruction 3 - 7

Tuesday, 14 June 2022

2000 Porsche Boxster (986) F6-2.7L A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Page 350


8021 Navigation



8021 Navigation



Open circuit in GPS antenna



Diagnostic conditions



- Ignition on



- PCM2 on



NOTE:



- Fault code 8003 is recorded in the PCM2 MMI if the operating buttons are actuated for '>= 1 Min.'.



- Deactivate the 'automatic traffic announcement' before performing the diagnosis on the PCM2. If this is not done, the diagnosis will abort.



Possible cause of fault



- Open circuit in the antenna wiring between GPS antenna and the PCM2



- GPS antenna faulty



- Navigation module faulty



- PCM2 faulty



NOTE:



- The MOST optical waveguide is connected to the following control modules:



- PCM2



- CD changer



- Amplifier



- Telephone/telematics

2000 Porsche Boxster (986) F6-2.7L A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Page 121


Front left speed sensor, open circuit/ short to ground/ short to B+



DTC 4205



Wire/plug connection between control module and speed sensor not OK (open circuit, short to B+ or short to ground) or the speed sensor itself is



damaged.



Check the speed sensor wire and plug connection in the wheel area for damage (visual inspection).



- Check the speed sensor signal with the Porsche System Tester 2 via the Actual values menu (see test point 2/diagnostic trouble code 4206). If



no speed is displayed when the left front wheel is turned, check the wiring from the control module connector to the speed sensor (following



test step).



- Pull off control module connector. Measure internal resistance/continuity between PIN 6 and PIN 7 on the connector.



Nominal value 1600...1800 Ohms.



If the nominal value is not achieved, check wires and plug connection in the wiring from the front left speed sensor.



If the nominal value (1600...1800 Ohms) is not achieved although the wiring / plug connection is OK, replace the speed sensor.



- Check PIN 6 and PIN 7 of the control module connector inspection for deformation).



Test Point 7



Test point 7



Front right speed sensor, open circuit/ short to ground/ short to B+



DTC 4200



General procedure as for test point 6/diagnostic trouble code 4205.



- Speed sensor signal: Check with the Porsche System Tester 2 via the Actual values menu (call up front right wheel speed).



- Internal resistance/continuity between PIN 4 and PIN 5 on the control module connector.



Test Point 8



Test point 8



Rear right speed sensor, open circuit/ short to ground/ short to B+



DTC 4210



General procedure as for test point 6/diagnostic trouble code 4205.



- Speed sensor signal: Check with the Porsche System Tester 2 via the Actual values menu (call up rear right wheel speed).



- Internal resistance/continuity between PIN 1 and PIN 2 on the control module connector.



Test Point 9



Test point 9



Rear left speed sensor, open circuit / short to ground / short to B+



DTC 4215



General procedure as for test point 6/diagnostic trouble code 4205.



- Speed sensor signal: Check with the Porsche System Tester 2 via the Actual values menu (call up rear left wheel speed).



- Internal resistance/continuity between PIN 8 and PIN 9 on the control module connector.

2000 Porsche Boxster (986) F6-2.7L A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Page 365


Part 3



8004 External Harman Amplifier



8004 External Harman amplifier



Fault in rear loudspeaker



Diagnostic conditions



- Ignition on



- PCM2/CDR23 ON



NOTE: Fault code 8003 is recorded in the PCM2 MM/ if the operating buttons are actuated for '>= 1 Min.'.



Possible cause of fault



- Short circuit to B+/ground in the wiring harness



- Short circuit - loudspeaker faulty



- Short circuit - amplifier faulty



Affected pin



External Harman amplifier, plug A, pin 24, pin 29, pin 25, pin 38



Diagnosis/troubleshooting

Monday, 13 June 2022

2000 Porsche Boxster (986) F6-2.7L A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Page 193


Display: infinity



- Door lock actuated towards "Open".



Display: < 5 ohms



Test Point 7



TEST POINT 7



Central Lock Button Closed, Short To B+



Fault Code 07



Fault Effect: No central locking possible



Procedure



1. Pull plug I off the alarm system control module.



2. Check switch for central locking.



Voltmeter at plug I, pin 29 and ground.



- Switch for central locking not actuated.



Display: 0 Volts



- Switch for central locking actuated towards "Closed".



Display: Battery voltage.



3. Disconnect plug connection on the switch for central locking.



4. Check the wire from the alarm system control module to the switch for central locking for short to B+.



Voltmeter at plug I, pin 29 and ground.



Display: 0 Volts



Test Point 8



TEST POINT 8



Central Lock Button Open, Short To B+



Fault Code 08



Fault Effect: No central locking possible



Procedure



1. Pull plug I off the alarm system control module.



2. Check the central locking button.



Voltmeter at plug I, pin 10 and ground.



- Switch for central locking not actuated.



Display: 0 Volts



- Switch for central locking actuated towards Open



Display: Battery voltage



3. Disconnect plug connection on the switch for central locking.



4. Check the wire from the alarm system control module to the switch for central locking for short to B+.

2000 Porsche Boxster (986) F6-2.7L A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Page 316


Work Instruction 1 - 5



Fault Code 9132



Fault Code 9132



Terminal 61



Diagnostic conditions



- Ignition on



Possible cause of fault



- Open circuit in the wire between instrument cluster and generator (terminal 61)



- Generator faulty



Affected pin



Instrument cluster connector A, pin 12



Diagnosis/Troubleshooting



Work Instruction 1 - 3

2000 Porsche Boxster (986) F6-2.7L A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Page 70


Instrument cluster connector B, pin 3 and pin 19



Diagnosis/troubleshooting



Part 1



Part 2



Fault Code 9130



Fault code 9130



Supply voltage



Diagnostic conditions



- Engine running



NOTE: The fault memory status (present / not present) is always updated when the motor is running.



Possible cause of fault



- Battery voltage too low



Affected pin



Instrument cluster connector A, pin 2, pin 3, pin 17, and pin 18



Diagnosis/troubleshooting

Sunday, 12 June 2022

2000 Porsche Boxster (986) F6-2.7L A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Page 336


Work Instruction 5 - 9



800C PCM2 MMI



800C PCM2 - MMI



Fault During Software Update Using Single CD



Diagnostic conditions



- Ignition on



- PCM2on



Possible cause of fault



- Incorrect/incompatible software version



- Third-party software components



NOTE:



The MOST optical waveguide is connected to the following control modules:



- PCM2 as of model year 2003



- CD changer



- Amplifier



- Telephone/telematics



Diagnosis/troubleshooting