2010 Porsche Boxster (987) F62.9L
Copyright ? 2013, ALLDATA
10.52SS
Page 1
Vehicle: All Technical Service Bulletins
PCM3.0(R) Bluetooth(R) Interface Retrofitting
PCM3.0 Bluetooth Handsfree Interface (Ino. 619)
Concerns:
Retrofitting
Model Year:
As of 2009
Restriction:
Only for vehicles with PCM3.0 (Ino. 665) or navigation system (lno. 672). Not in conjunction with telephone module (Ino. 666).
Note:
The mobile phone preparation is available without a console for connecting mobile phones that support the handfree profile (HFP) via
Bluetooth(R). When connected over HFP, PCM3.0 serves only as a handsfree facility. The mobile phone can remain packed. The
telephone numbers from the SIM card must be copied over manually, unlike with the telephone module. Only the basic functions of the
mobile phone can be used using PCM3.0 (see PCM3.0 operating instructions). With this option, GSM is connected via the mobile phone
antenna.
If a mobile phone is installed and activated even though the telephone module is installed, the telephone module is not required. Both
systems cannot be used at the same time.
After ordering, i.e. entering the part number and Vehicle Identification Number (VIN) in POLARIS Lock/Key parts order screen, the
enabling code should be displayed within one day once the VIN is entered in the Vehicle code information column in the PIWIS
information system.
Parts Info:
997.044.902.34 Standard phone preparation, set
Parts List:
Materials:2010 Porsche Boxster (987) F62.9L
Copyright ? 2013, ALLDATA
10.52SS
Page 2
Wrapping tape (commercially available)
Tools:
PIWIS Tester 9718
Pressout tool set Nr. 155 Pos.l
System Diagram:
INFORMATION For a better understanding of the system layout, see system diagram, Figure 3.
Work Procedure:
INFORMATION
If a wire harness for microphones does not need to be installed (for details of options, see Step 2.1 Overview of installing microphone
wire harness), only Steps 1.1 and 4.4 have to be completed Enable mobile phone preparation.
1 Preparatory work.
1.1 Connect battery charger.>Workshop Manual '2XOO1NO3 Battery trickle charging'
1.2 Remove PCM3.0.>Workshop Manual '911019 Removing and installing PCM display and operator control unit
1.3 Remove trim panel under dashboard.>Workshop Manual '701919 Removing and installing trim panel under
dashboard'Checking
2 Install microphone wire harness.
INFORMATION The table shows whether a microphone wire harness needs to be retrofitted.
2.1 Overview of installing microphone wire harness:
Vehicle equipment
BOSE sound package (lno. 680)
ASK sound package (lno. 490)
Telephone module (lno. 666)
Telephone module (lno. 666)
in conjunction with lnos. 490, 680.
Voice control system (lno. 671)
Voice control system (lno. 671)
in conjunction with lnos. 490, 666, 680.
Microphone wire harness Installation
Yes
Yes
No
No
No
No2010 Porsche Boxster (987) F62.9L
Copyright ? 2013, ALLDATA
10.52SS
Page 3
2.1 Prepare wire harness for microphone.
2.2.1 Open lock on white connector housing > Figure 41
INFORMATION Ensure socket contact is seated securely.
2.2.2 Insert socket contact of line BU 0.35(squared) into chamber 1 of the white connector housing.
Insert socket contact of line YE 0.35(squared) into chamber 2 of the white connector housing.
2.2.3 Close lock on white connector housing.
2.2.4 Lift up locking mechanism >Figure 5 arrow A on wire harness for microphones and pull the plug socket =>Figure 5
1 out of the plug carrier >Figure 5 arrow B.
2.3 Open wiring duct >Figure 61.2010 Porsche Boxster (987) F62.9L
Copyright ? 2013, ALLDATA
10.52SS
Page 4
2.4 Route wire harness for microphones >Figure 71 and secure with a tiewrap or wrapping tape.
Steering column =>Figure 7 2 > into wiring duct >Figure 73 > main wire harness >Figure 74 > PCM installation slot
2.5 Close wiring duct.
INFORMATION Socket contacts also need to be changed, depending on the vehicle equipment.
2.6 Only for vehicles with BOSE sound system (lno. 680) or ASK sound package (kio. 490) or TVtuner(lno. 676):
Change socket contacts.
2.6.1 Overview of socket contacts to be changed.
2.6.2 Press locking mechanism down > Figure 8 arrow A and pull standard connector module C (coding blue) > Figure 8
1 out of the PCM central connector > Figure 8 2 (>Figure arrow B)2010 Porsche Boxster (987) F62.9L
Copyright ? 2013, ALLDATA
10.52SS
Page 5
2.6.3 Lift up locking mechanism >Figure 9 arrow A and pull the plug socket >Figure 9 1 out of the plug carrier >Figure
9 arrow B.
INFORMATION Ensure socket contact is seated securely.
2.6.4 Press socket contact of WH/RD line (chamber C4), for example, out of the standard connector housing >Figure 10 1
using a pressout tool and insert it into the connector housing (retrofit kit)
2.7 Insert plug socket >Figure 11 1 into plug carrier Figure 11 2.
2.8 Insert connector module C (coding: blue) >Figure 12 arrow from the microphone wire harness into the PCM central
connector.2010 Porsche Boxster (987) F62.9L
Copyright ? 2013, ALLDATA
10.52SS
Page 6
2.9 Only for vehicles with BOSE sound package (lno. 680):
2.9.1 Open lock on microphone connector housing >Figure 13 1.
2.9.2 Press socket contacts out of the connector housing using pressout tool 88089.
INFORMATION Ensure socket contact is seated securely.
2.9.3 Insert socket contact of line RD 0.5sq. into chamber 3 of the white connector housing >Figure 14 1
Insert socket contact of line RD/BN; 0.5(squared) into chamber 4 of the white connector housing.
2.9.4 Close lock on white connector housing.
3
Install microphones.
INFORMATION Either two microphones or no microphones must be retrofitted, depending on the vehicle equipment.
3.1 Overview of microphone fixtures
Vehicle equipment
BOSE sound package (lno. 680)
ASK sound package (lno. 490)
Telephone module (lno. 666)
Telephone module (lno. 666)
in conjunction with lnos. 490, 680.
Voice control system (lno. 671)
Voice control system (lno. 671)
in conjunction with lnos. 490, 666, 680.
3.2 Install microphone.
Microphone Installation
Yes
Yes
No
No
No
No2010 Porsche Boxster (987) F62.9L
Copyright ? 2013, ALLDATA
10.52SS
Page 7
3.2.1 Unclip the standard microphone (e.g. BOSE sound system, coding: black) >Figure 151from the trim panel.
3.2.2 Clip sound microphone/handsfree microphone (coding: white) >Figure 162 and handsfree microphone (coding: light
blue) >Figure 161 into the trim panel.
4
Concluding work
4.1
4.2
Fit new tiewraps >Figure 17 1 on trim panel under the dashboard.
Install trim panel under dashboard (driver's side).>Workshop Manual '701919 Removing and installing trim panel under
dashboard'
4.3 Install PCM3.0.>Workshop Manual '911019 Removing and installing PCM display and operator control unit
NOTICE
Voltage drop
Risk of irreparable damage to control unit
Risk of damage to control unit
Fault entries in the control unit
Coding in the control unit is aborted
Malfunctions in control unit, even during programming
Switch off the ignition and remove the ignition key before disconnecting the control unit.
Ensure that the power supply is not interrupted during programming.
Connect a battery charger with a current rating of at least Nominal value 40 A to the vehicle battery.2010 Porsche Boxster (987) F62.9L
Copyright ? 2013, ALLDATA
10.52SS
Page 8
INFORMATION
The PIWIS Tester 9718 instructions take precedence and in the event of a discrepancy these are the instructions that must be
followed. Deviations may occur with later software versions.
The procedure described here has been structured in general terms; different text or additions may appear in the PIWIS Tester
9718.
4.4 Enable mobile phone preparation.
4.4.1 PIWIS Tester 9718 must be connected and ignition switched on.
4.4.2 Select vehicle type and run control unit search.
4.4.3 Select PCM3 control unit.
4.4.4 Select PCM3 in the PCM3 function selection menu. Press F12 to continue.
4.4.5 Select Coding in the PCM3 function selection menu. Press F12 to continue.
4.4.6 Select Enabling code in the PCM3/Coding menu. Press F12 to continue.
INFORMATION The PIWIS Tester 9718 displays the message not installed/not enabled/not operational.
4.4.7 Select Enabling code for Bluetooth mobile phone preparation in the PCM3.0/Enabling code menu. Press F12 to
continue.
4.4.8 Enter the enabling code and press F8 to start coding. PIWIS Tester 9718 then displays the message
installed/enabled/functional.
4.4.9 Press F11 to return to the main menu. The system is initialized.
4.4.10 Once coding is complete, read out the fault memories of all systems, correct any existing faults and erase the fault
memories.
4.4.11 Switch off ignition and disconnect PIWIS Tester 9718.
4.4.12 Disconnect the battery charger.>Workshop Manual '2XOO1NO3 Battery trickle charging'
Working Time:
Disclaimer
Copyright ? 2013, ALLDATA
10.52SS
Page 1
Vehicle: All Technical Service Bulletins
PCM3.0(R) Bluetooth(R) Interface Retrofitting
PCM3.0 Bluetooth Handsfree Interface (Ino. 619)
Concerns:
Retrofitting
Model Year:
As of 2009
Restriction:
Only for vehicles with PCM3.0 (Ino. 665) or navigation system (lno. 672). Not in conjunction with telephone module (Ino. 666).
Note:
The mobile phone preparation is available without a console for connecting mobile phones that support the handfree profile (HFP) via
Bluetooth(R). When connected over HFP, PCM3.0 serves only as a handsfree facility. The mobile phone can remain packed. The
telephone numbers from the SIM card must be copied over manually, unlike with the telephone module. Only the basic functions of the
mobile phone can be used using PCM3.0 (see PCM3.0 operating instructions). With this option, GSM is connected via the mobile phone
antenna.
If a mobile phone is installed and activated even though the telephone module is installed, the telephone module is not required. Both
systems cannot be used at the same time.
After ordering, i.e. entering the part number and Vehicle Identification Number (VIN) in POLARIS Lock/Key parts order screen, the
enabling code should be displayed within one day once the VIN is entered in the Vehicle code information column in the PIWIS
information system.
Parts Info:
997.044.902.34 Standard phone preparation, set
Parts List:
Materials:2010 Porsche Boxster (987) F62.9L
Copyright ? 2013, ALLDATA
10.52SS
Page 2
Wrapping tape (commercially available)
Tools:
PIWIS Tester 9718
Pressout tool set Nr. 155 Pos.l
System Diagram:
INFORMATION For a better understanding of the system layout, see system diagram, Figure 3.
Work Procedure:
INFORMATION
If a wire harness for microphones does not need to be installed (for details of options, see Step 2.1 Overview of installing microphone
wire harness), only Steps 1.1 and 4.4 have to be completed Enable mobile phone preparation.
1 Preparatory work.
1.1 Connect battery charger.>Workshop Manual '2XOO1NO3 Battery trickle charging'
1.2 Remove PCM3.0.>Workshop Manual '911019 Removing and installing PCM display and operator control unit
1.3 Remove trim panel under dashboard.>Workshop Manual '701919 Removing and installing trim panel under
dashboard'Checking
2 Install microphone wire harness.
INFORMATION The table shows whether a microphone wire harness needs to be retrofitted.
2.1 Overview of installing microphone wire harness:
Vehicle equipment
BOSE sound package (lno. 680)
ASK sound package (lno. 490)
Telephone module (lno. 666)
Telephone module (lno. 666)
in conjunction with lnos. 490, 680.
Voice control system (lno. 671)
Voice control system (lno. 671)
in conjunction with lnos. 490, 666, 680.
Microphone wire harness Installation
Yes
Yes
No
No
No
No2010 Porsche Boxster (987) F62.9L
Copyright ? 2013, ALLDATA
10.52SS
Page 3
2.1 Prepare wire harness for microphone.
2.2.1 Open lock on white connector housing > Figure 41
INFORMATION Ensure socket contact is seated securely.
2.2.2 Insert socket contact of line BU 0.35(squared) into chamber 1 of the white connector housing.
Insert socket contact of line YE 0.35(squared) into chamber 2 of the white connector housing.
2.2.3 Close lock on white connector housing.
2.2.4 Lift up locking mechanism >Figure 5 arrow A on wire harness for microphones and pull the plug socket =>Figure 5
1 out of the plug carrier >Figure 5 arrow B.
2.3 Open wiring duct >Figure 61.2010 Porsche Boxster (987) F62.9L
Copyright ? 2013, ALLDATA
10.52SS
Page 4
2.4 Route wire harness for microphones >Figure 71 and secure with a tiewrap or wrapping tape.
Steering column =>Figure 7 2 > into wiring duct >Figure 73 > main wire harness >Figure 74 > PCM installation slot
2.5 Close wiring duct.
INFORMATION Socket contacts also need to be changed, depending on the vehicle equipment.
2.6 Only for vehicles with BOSE sound system (lno. 680) or ASK sound package (kio. 490) or TVtuner(lno. 676):
Change socket contacts.
2.6.1 Overview of socket contacts to be changed.
2.6.2 Press locking mechanism down > Figure 8 arrow A and pull standard connector module C (coding blue) > Figure 8
1 out of the PCM central connector > Figure 8 2 (>Figure arrow B)2010 Porsche Boxster (987) F62.9L
Copyright ? 2013, ALLDATA
10.52SS
Page 5
2.6.3 Lift up locking mechanism >Figure 9 arrow A and pull the plug socket >Figure 9 1 out of the plug carrier >Figure
9 arrow B.
INFORMATION Ensure socket contact is seated securely.
2.6.4 Press socket contact of WH/RD line (chamber C4), for example, out of the standard connector housing >Figure 10 1
using a pressout tool and insert it into the connector housing (retrofit kit)
2.7 Insert plug socket >Figure 11 1 into plug carrier Figure 11 2.
2.8 Insert connector module C (coding: blue) >Figure 12 arrow from the microphone wire harness into the PCM central
connector.2010 Porsche Boxster (987) F62.9L
Copyright ? 2013, ALLDATA
10.52SS
Page 6
2.9 Only for vehicles with BOSE sound package (lno. 680):
2.9.1 Open lock on microphone connector housing >Figure 13 1.
2.9.2 Press socket contacts out of the connector housing using pressout tool 88089.
INFORMATION Ensure socket contact is seated securely.
2.9.3 Insert socket contact of line RD 0.5sq. into chamber 3 of the white connector housing >Figure 14 1
Insert socket contact of line RD/BN; 0.5(squared) into chamber 4 of the white connector housing.
2.9.4 Close lock on white connector housing.
3
Install microphones.
INFORMATION Either two microphones or no microphones must be retrofitted, depending on the vehicle equipment.
3.1 Overview of microphone fixtures
Vehicle equipment
BOSE sound package (lno. 680)
ASK sound package (lno. 490)
Telephone module (lno. 666)
Telephone module (lno. 666)
in conjunction with lnos. 490, 680.
Voice control system (lno. 671)
Voice control system (lno. 671)
in conjunction with lnos. 490, 666, 680.
3.2 Install microphone.
Microphone Installation
Yes
Yes
No
No
No
No2010 Porsche Boxster (987) F62.9L
Copyright ? 2013, ALLDATA
10.52SS
Page 7
3.2.1 Unclip the standard microphone (e.g. BOSE sound system, coding: black) >Figure 151from the trim panel.
3.2.2 Clip sound microphone/handsfree microphone (coding: white) >Figure 162 and handsfree microphone (coding: light
blue) >Figure 161 into the trim panel.
4
Concluding work
4.1
4.2
Fit new tiewraps >Figure 17 1 on trim panel under the dashboard.
Install trim panel under dashboard (driver's side).>Workshop Manual '701919 Removing and installing trim panel under
dashboard'
4.3 Install PCM3.0.>Workshop Manual '911019 Removing and installing PCM display and operator control unit
NOTICE
Voltage drop
Risk of irreparable damage to control unit
Risk of damage to control unit
Fault entries in the control unit
Coding in the control unit is aborted
Malfunctions in control unit, even during programming
Switch off the ignition and remove the ignition key before disconnecting the control unit.
Ensure that the power supply is not interrupted during programming.
Connect a battery charger with a current rating of at least Nominal value 40 A to the vehicle battery.2010 Porsche Boxster (987) F62.9L
Copyright ? 2013, ALLDATA
10.52SS
Page 8
INFORMATION
The PIWIS Tester 9718 instructions take precedence and in the event of a discrepancy these are the instructions that must be
followed. Deviations may occur with later software versions.
The procedure described here has been structured in general terms; different text or additions may appear in the PIWIS Tester
9718.
4.4 Enable mobile phone preparation.
4.4.1 PIWIS Tester 9718 must be connected and ignition switched on.
4.4.2 Select vehicle type and run control unit search.
4.4.3 Select PCM3 control unit.
4.4.4 Select PCM3 in the PCM3 function selection menu. Press F12 to continue.
4.4.5 Select Coding in the PCM3 function selection menu. Press F12 to continue.
4.4.6 Select Enabling code in the PCM3/Coding menu. Press F12 to continue.
INFORMATION The PIWIS Tester 9718 displays the message not installed/not enabled/not operational.
4.4.7 Select Enabling code for Bluetooth mobile phone preparation in the PCM3.0/Enabling code menu. Press F12 to
continue.
4.4.8 Enter the enabling code and press F8 to start coding. PIWIS Tester 9718 then displays the message
installed/enabled/functional.
4.4.9 Press F11 to return to the main menu. The system is initialized.
4.4.10 Once coding is complete, read out the fault memories of all systems, correct any existing faults and erase the fault
memories.
4.4.11 Switch off ignition and disconnect PIWIS Tester 9718.
4.4.12 Disconnect the battery charger.>Workshop Manual '2XOO1NO3 Battery trickle charging'
Working Time:
Disclaimer